Plumbing and Electrical Layout for Home Construction in Pakistan: A Practical Guide
Key takeaways
- Plan services before plaster, tiles and false ceilings hide them.
- Design around how your family lives: ACs, geysers, pump, UPS or solar, kitchen appliances.
- Keep valves, inspection chambers and junction boxes accessible.
- Let a qualified engineer size pipes, cables and breakers. Never copy a neighbour’s layout.
- Test everything, and photograph pipe and cable routes before they are covered.
Most homeowners spend months choosing tiles, paint and kitchen cabinets. Yet the parts that decide whether a house works well, such as water pipes, drains, wiring and the distribution board, disappear behind plaster within weeks. When one of them is wrong, the repair usually means breaking a finished wall or floor.
In Pakistan this matters even more. Houses on 5 Marla, 10 Marla and 1 Kanal plots must cope with load-shedding, heavy air-conditioning loads, water tanks and pumps, and often a solar or inverter system. This guide explains what the layouts contain, how to coordinate them, and what to check before you approve drawings or let workers start.
What Is a Plumbing and Electrical Layout?
These drawings show where water pipes, drainage lines, wiring, lights, switches, sockets and protective devices will be installed. They must follow the architectural floor plan so that fixtures, furniture and services agree with each other.
- Plumbing layout: brings clean water in and takes wastewater out. It typically shows supply pipes, drains, tanks, the pump, valves, fixtures and inspection chambers, backed by a pipe schedule and bill of quantities. A plumbing or public health designer prepares it.
- Electrical layout: distributes power safely to lights, fans, sockets and appliances. It typically shows light and fan points, switches, sockets, conduit routes, the distribution board and earthing, backed by a load calculation, load schedule and circuit schematic. A qualified electrical engineer or designer prepares it.
When combined with ventilation and other building services, the full set is called MEP (mechanical, electrical and plumbing) drawings. Larger homes, and houses with solar, generators or special equipment, benefit most from a complete MEP package.
Why These Layouts Matter
Good planning prevents problems that are slow and expensive to fix once the house is finished. These are the mistakes that most often cost owners money:
- Drain moved after tiling: means a broken floor, new tiles and repeated waterproofing. Fixing fixture and drain positions before work starts prevents it.
- Socket hidden behind a wardrobe or bed: leads to extension boards and unsafe daisy-chaining. Place sockets against the furniture plan instead.
- AC added later to an overloaded circuit: causes tripping breakers and overheated cables. Plan dedicated circuits and spare capacity early.
- Valve buried behind tiles: forces wall demolition for a small leak. Mark valves and access panels on the drawing.
- Conduit routes left unplanned: result in surface wiring and damaged plaster. Mark routes before plastering.
Safety is the other reason. Electrical faults are a recognised cause of house fires, and undersized cables, missing earthing or absent protective devices raise the risk. Poor plumbing leads to damp, blocked drains and damage that spreads to ceilings below. These faults stay hidden until they become serious, so they must be designed and checked while the work is still visible.
Plumbing Layout: What to Plan
Water Supply
Most Pakistani homes store water. A city connection or bore feeds an underground tank, a pump lifts water to an overhead tank, and gravity or a booster pump serves the fixtures. Your drawing should show:
- The incoming connection, meter or bore location
- Underground tank position, capacity, cleaning access and overflow route
- Pump location, protected from water and dry running
- Overhead tank position, high enough above the top fixture for good pressure, with an overflow pipe
- Separate hot and cold lines, the geyser location, and insulation on hot-water pipes
- An isolation valve for each bathroom, the kitchen and outdoor taps
Tank capacity and pipe diameters should be calculated by a qualified professional from the number of fixtures and expected demand, not guessed from plot size. PPR is commonly used for hot and cold supply and uPVC for drainage, but the designer should confirm materials against pressure, temperature and manufacturer instructions.
Drainage and Sewerage
Wastewater must flow away without blockages or odours. The drawing should trace every route from toilets, basins, showers, sinks and floor traps to the sewer connection, or to a septic tank and soakage pit where no sewer exists.
- Use a steady downward slope and avoid needless bends. The correct slope depends on pipe diameter (often around 1 in 40 for 4-inch drains), so confirm it with your designer.
- Add vent pipes so traps keep their water seal and bathrooms stay odour-free.
- Place inspection chambers at changes of direction and near the boundary wall.
- Keep rainwater separate from household wastewater.
- Locate septic tanks and soakage pits well away from water tanks and bores, following local rules on distances.
Bathroom and Kitchen Plumbing
These rooms pack many fixtures into small areas, so they need the closest coordination.
- Choose sanitary ware, sinks and cabinets before fixing pipe positions, because rough-in dimensions differ between models.
- Waterproof bathroom floors and wet walls, then flood-test the floor (commonly 24 to 48 hours) before tiling.
- Pressure-test supply pipes before they are covered.
- In the kitchen, plan points for the sink, water filter, washing machine, dishwasher and gas appliances.
- Fit accessible isolation valves wherever practical.
Electrical Layout: What to Plan
Lighting and Fan Points
Lighting should suit each room’s size, ceiling height, daylight and use. Bedrooms need soft general light with bedside control, kitchens need bright task lighting over worktops, and stairs, porches and gardens need safe lighting after dark.
- Use two-way switching on staircases and long corridors.
- Make porch and gate lights controllable from indoors.
- Fit fan boxes and hooks rated for the fan’s weight.
- Match light positions to false ceiling and cove-lighting designs.
- Mark the lights and fans that must keep running during outages.
Switches and Sockets
Place switches and sockets where people will really use them: near door swings, beds, desks, worktops and TV walls. The list below shows what many families find useful, but your own furniture plan should decide the final positions.
- Bedroom: sockets on both sides of the bed, a dresser or TV point, a dedicated AC point, USB charging, and switches at the door and bedside.
- Lounge: several sockets on the TV wall (TV, router, set-top box, console), a dedicated AC point, and floor-lamp sockets.
- Kitchen: separate counter sockets for small appliances, plus dedicated points for the fridge, oven, microwave, washing machine and exhaust fan.
- Bathroom: an isolator switch for the geyser, an exhaust fan point, and any sockets kept outside splash zones and RCD-protected.
- Outdoors: weatherproof sockets and fittings, a gate light, and power for the gate motor and CCTV.
- Study or home office: desk sockets, networking points and a UPS connection.
Heavy appliances should have their own circuits rather than sharing with other devices.
Distribution Board and Circuit Planning
The distribution board (DB) splits the supply into separate circuits and houses the breakers that protect them. The designer should complete an electrical load calculation (the combined demand of lights, sockets, ACs, geysers, pumps and other appliances) and then prepare a load schedule listing each circuit, its load and its protective device.
Typical circuits, with commonly used cable sizes:
- Lighting: keep it separate so one fault does not black out the whole house. Commonly 1.5 mm².
- General sockets: higher current, with RCD protection. Commonly 2.5 mm².
- Each air conditioner: high load and starting current. Commonly 4 mm².
- Geyser: heavy, continuous load. Commonly 4 mm².
- Oven or heavy kitchen appliance: large, usually fixed load. Commonly 4 to 6 mm².
- Water pump: motor load that needs motor-rated protection. Size as per the motor rating.
The cable sizes above are indicative only. Final sizes depend on load, cable length, installation method, voltage drop and the applicable code, and must be confirmed by your electrical engineer.
Every installation needs effective earthing that connects the DB, sockets and metal appliance bodies to an earth electrode, plus residual current devices (commonly 30 mA for socket and wet-area circuits) that cut power quickly during leakage faults. Leave spare ways in the DB for future circuits. Residential supply in Pakistan is normally 230 V single-phase, but a large house with many air conditioners may need a higher sanctioned load or a three-phase connection, so raise this early with your electricity distribution company.
Backup Power and Solar
Because of load-shedding, many homes include a UPS, inverter or solar system. Plan it during wiring, not after plastering.
- Create a separate “essential loads” board for lights, fans, fridge, router and chargers, so backup power is not drained by ACs and geysers.
- Reserve roof space and cable routes for panels, plus a ventilated inverter location, DC isolation and surge protection.
- Use a proper changeover switch with a generator so power cannot feed back into the utility network, which endangers line staff.
If you plan net metering, check the current rules of your distribution company and NEPRA first, as policies change.
How to Coordinate Plumbing, Electrical and Architectural Drawings
Pipes and conduits often share walls, shafts and ceiling spaces. Reviewing the drawings together exposes clashes on paper instead of on site. A practical sequence:
- Freeze the architectural plan: confirm bathrooms, kitchen, stairs, furniture and appliances.
- Check with the structural engineer: agree openings and sleeves through beams and slabs. Never cut beams or columns to fit pipes.
- Mark plumbing: fixtures, shafts, drains, tanks and pump.
- Mark electrical: points, conduit routes, DB position and loads.
- Overlay the drawings: resolve clashes, and keep water pipes away from the DB and other electrical equipment.
- Prepare quantities: material estimates for pipes, cables, conduits and fittings.
- Install in sequence: place sleeves before slab casting, and embed pipes and conduits before plastering.
- Test and record: carry out pressure, flood and electrical tests, then photograph the routes before covering them so future repairs know where pipes and cables run.
In double-storey houses, aligning bathrooms and kitchens above one another simplifies drainage shafts. Always work from the latest approved drawings.
Layout Considerations by House Size
A standard Marla is 272.25 sq ft, although some housing societies use a different Marla size, so check your approved plan. Covered area alone does not set the design. The number of bathrooms, ACs, appliances and outdoor facilities matters just as much.
| Aspect | 5 Marla | 10 Marla | 1 Kanal |
|---|---|---|---|
| Approx. plot area | 1,361 sq ft | 2,722 sq ft | 5,445 sq ft |
| Plumbing focus | Stack bathrooms to share one shaft; compact tank and pump placement | Multiple bathrooms, laundry and outdoor taps; drainage coordinated between floors | Longer pipe runs (may need a booster pump), several shafts, garden taps or irrigation |
| Electrical focus | Compact DB; AC points planned even if ACs come later | Sub-boards per floor; dedicated circuits for ACs and kitchen | Sub-distribution boards, possible three-phase supply, solar, generator, gate and CCTV power |
Whatever the size, earthing, circuit protection and accessible valves are never optional. On a 1 Kanal plot, also consider provisions for EV charging and landscape lighting while the cables are still easy to route.
How Much Do Layout Drawings Cost in Pakistan?
Costs depend on house size, number of floors, complexity and the level of detail. A basic package may show only point locations, while a fuller one includes circuit schedules, load calculations, drainage details and material quantities. Rates vary by city and consultant, so request a written quotation instead of relying on a general figure. Drawing fees are also separate from the cost of pipes, cables, fittings and labour.
Main factors that affect the price:
- House size and floors: larger or multi-storey homes need more detailed drawings and coordination.
- Complexity: more bathrooms, appliances and special systems add work.
- Detail level: load calculations, schedules and service routes take extra time.
- Quantities: a bill of quantities may be priced separately.
- Site visits and special systems: inspections, and solar, inverter, generator and CCTV drawings, may cost extra.
Ask every consultant which drawings are included, how many revisions are allowed, whether load calculations and quantities are covered, and whether they will coordinate with your architect.
Who Should Prepare Your Layouts?
Layouts should be prepared or reviewed by professionals with suitable training and residential experience. The architect coordinates them with the floor plan, a qualified electrical engineer handles loads, circuits, cable selection, earthing and protection, and a plumbing designer plans supply, drainage and pipe sizes. Before hiring, check:
- Pakistan Engineering Council (PEC) registration of the engineers involved
- Previous residential projects, ideally with sample drawings
- A written scope covering revisions, estimates and site support
Review and approve the final drawings before installation, and have any site change checked by the relevant professional first.
Standards and Authorities to Check
Requirements vary by city and housing scheme, so verify these before finalizing the design:
- Your local development or building control authority and housing society rules, including your approved building plan
- Your electricity distribution company (for example LESCO, IESCO or K-Electric) for sanctioned load, meter and solar rules
- WASA or your local water and sanitation agency for water and sewer connection rules
- SNGPL or SSGC if you will use gas; gas piping should be installed only by authorised contractors
- The Building Code of Pakistan provisions published by PEC, and the electrical code or standard your engineer designs to
- Manufacturer instructions for pipes, pumps, geysers, inverters and breakers
Conclusion: Plan Before You Build
A well-planned plumbing and electrical layout makes a home safer, more practical and easier to maintain. Whether you are building 5 Marla, 10 Marla or 1 Kanal, review the drawings with qualified professionals before construction starts, confirm they match the architectural and structural designs, and leave room for future needs such as extra ACs or solar.
If you are planning a house in Pakistan, AQsons Group of Companies offers architectural design and construction services to help you plan from the first sketch to completion. Good planning today saves time, money and frustration for years.
Frequently Asked Questions
1. When should plumbing and electrical layouts be prepared?
During the design stage, alongside the architectural drawings and before slabs are cast or walls plastered. This leaves time to confirm fixtures, calculate loads and coordinate routes.
2. Are drawings necessary for a new house?
Submission requirements depend on your authority and project, but detailed drawings are strongly recommended. They let you check socket positions and fixtures before work begins and stop workers improvising on site.
3. Can the layout change during construction?
Yes, but review each change first. Moving a socket may need rewiring, while moving a toilet affects drainage, floor levels and waterproofing. Update the drawings so everyone works from the same plan.
4. How many sockets does a room need?
There is no fixed number. Plan from your furniture layout and appliance list, then add a few spare points. Adding a point on paper costs almost nothing; adding it after plastering does.
5. Do I need an electrical load calculation?
Yes. It estimates demand from lights, sockets, ACs, geysers and pumps, and guides cable sizes, breaker ratings and the connection load you apply for.